![]() The settings are then stored in a dedicated battery-backed memory, called CMOS RAM, that retains the information when the power is turned off. The Setup program lets you modify basic system configuration settings. Setting: Y (Please note: enter Z with German keyboard). This manual describes the Phoenix Technologies AwardBIOS Setup program. Input: Y (Please note: enter Z with German keyboard). At first start of the BIOS, optimized values are loaded from the setup, which are. This option is used to save the settings and exit setup. Here you can enter a setup password for preventing unauthorised invoking of the BIOS. Advanced Chipset Features This setup page includes all the items of chipset special features. Advanced BIOS Features This setup page includes all the items of Award special enhanced features. ![]() This option is used for setting optimum values as recommended by the manufacturer. Standard CMOS Features This setup page includes all the items in standard compatible BIOS. If you are an end user in need of BIOS-related support, please contact the manufacturer of your product. It is not suitable for continuous operation, but can be useful if the PC malfunctions. Note: Phoenix Technologies licenses our firmware (BIOS) products to device manufacturers (OEMs) and partners. This option is used for absolute security settings. An "x" before a menu item indicates that there is a setting option that has to be activated via a setting at a higher level. "Brief description of the function selected above"Ī „►“ sign in front of the menu item indicates that a submenu is available. Top menuĮSC: Quit ↑ ↓ → ← Select ItemF10: Save & Exit Setup See also "Load Fail-Safe Defaults" and "Load Optimized Defaults". Once a setup setting that subsequently led to successful booting was saved, both menu items will load these values as default for the setup pages. The situation is different if the defaults are called from the TOP menu. These default values are applied irrespective of whether the board was previously booted successfully with a particular setup setting. Within the individual setup pages, F6 can be used for loading fail-safe defaults, and F7 for optimised default values for the individual setup entries. Any change in the addresses or interrupts would lead to unstable system behaviour or even crashing. The CX50x0 systems are delivered by Beckhoff Automation GmbH in a preconfigured state and are therefore operational! The BIOS settings should only be executed by appropriately trained staff.Under Windows CE the BIOS should not be changed at all, since the operating system is adapted to the hardware configuration. Thankyou in advance to whoever attempts to help.Changes in the BIOS settings may only be implemented by appropriately trained staff. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. Setzen Sie den Clear CMOS Jumper von der Normalposition (Stifte 1 und 2) auf die Löschposition (Stifte 2-3) und warten Sie etwa 2 Minuten ab. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. Um den CMOS Ihres Rechners per Jumper zurückzusetzen, führen Sie die folgenden Schritte aus: Trennen Sie den Rechner vom Stromnetz. There is something, obviously, but I can't find it. Some setting somewhere that I didn't configure right. So please, somebody, anybody, please tell me something that I'm not seeing. I know there are a lot of people out there smarter than me when it comes to computers. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. Bios and wt os are not recognizing the drive as being there at all. i put it on IDE, set it so PATA is primary, SATA is secondary. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says 'SATA mode'. I went back into the bios and checked it all again. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. When i first got it, I had a really hard time putting in more than one hard drive. I have a custom built comp with a Fatal1ty AA8XE mobo. These default settings are optimal and enable all high performance features.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |